Ambient Energy Aqua Purge Device Journal
A little later than expected, the adventures in steampunk have been documented… The Ambient Energy Aqua Purge Device Journal is finally live on the project pages. Hope some of you find it useful. Enjoy.
| Tweet |
Flowering Elbow
Invent Design Make
- Blog
- Blog
- Make Your Own
- Make your own Lathe from other peoples rubbish
- 0 – Introduction
- 1 – Acquiring the motor
- 2 – Motor speed control
- 3 – On/Off Switch
- 4 – Electronic Braking
- 5- The Lathe Bed
- 6 – The Headstock
- 7 – Making the headstock
- 8 – Making the central supports
- 9 – Mounting the motor
- 10 – Attaching the headstock to the bed
- 11 – Wiring up
- 12 – Housing the moving bits and making it look nice
- 13- The viewing window
- 14- Speed measurement (optional little interlude)
- 15 -The tailstock (part1)
- 16- The tailstock (part2)
- 17 -The tool rest
- 18 – Parting thoughts
- ‘Broken’ to ‘Super’ Drill
- From Sewing Machine to Scroll Saw
- Ambient Energy Aqua Purge Device
- Entry 1 – Beginnings
- Entry 2 – Acquiring Items
- Entry 3 – Making the End Supports
- Entry 4 – The Purging Rails
- Entry 5 – The Elevating Mechanism (overview)
- Entry 6 – Cleat Construction
- Entry 7 – End Pulley Support
- Entry 8 – Middle Bi-pulley Support
- Entry 9 – Corner Pulley
- Entry 10 – Fitting The AEAPD Hardware
- Entry 11 – The Purge Assembly Anchors
- Entry 12 – Fit the Purging Assembly
- Entry 13- Use…
- The Cyclone Dust Separator
- The Problem of Wood Dust – A Cyclonic Solution?
- Cyclonic Dust Separation – Overview
- Cyclone build part 1 – The Cone
- Cyclone build part 2 – Air Inlet and Ramp
- Cyclone build part 3 – the ‘Air Outlet’
- Cyclone build part 4 – The Upper Body
- Cyclone build part 5 – Putting it Together
- Resources and References
- Composite Oak French Doors / Windows: make your own
- French Composite Oak Doors – Intro
- 1 – Specifying the Glass (i)
- 2 – Specifying the Glass (ii)
- 3 – Designing your Doors
- 4 – Other Design Considerations
- 5 – Write a ‘cutting list’
- 6 – Get some wood
- 7 – Cut to size
- 8 – Prepare Channels for Weather seals
- 9 – Constructing the Frame part 1 – Laminating the Oak
- 10 – Constructing the Frame part 2 – Making a Rectangle
- 11 – Constructing the Doors Part 1 – Making the Rails and Stiles
- 12 – Constructing the Doors Part 2 – Adding the outer glass housing
- 13 – The Central Jambs & Multipoint Lock
- 14 – Going Composite & Adding Insulation
- 15 – Hinges
- 16 – The Central Rain Cover and Sills
- 17 – Test Hanging the Doors
- 18 – Finishing the Oak Surface
- 19 – Preparing the Entryway
- 20 – Installing the Oak Frames
- 21 – Glazing the Doors
- 22 – Finishing Touches & Door Handle
- Earth and Clay Plaster
- 0 – Clay Plaster Introduction
- 1 – Before you begin
- 2 – Soil testing
- 3 – Plaster testing for the first coat
- 4 – Prepare the walls
- 5 – Gather equipment and prepare resources
- 6 – Get set, go! Slip and plaster mixing in general
- 7 – First coat application
- 8 – Second coat testing
- 9 – Second coat mixing and application
- 10 – Finish coat plaster testing
- 11 – Third coat mixing and application
- 12 – Finishing
- Time Scale and Costings
- Resources for Clay plastering
- Make your own Lathe from other peoples rubbish
- About FE
- Contact
FE on
Blog
- Automated door from an old windscreen wiper motor
- I did not expect to be using the CNC like this
- The DIY CNC Router cuts steel!
- A New Book about Chainsaw Milling
- How to make Slug-Proof Raised Beds, uncommon yet simple design
- Posts that see out the century! How to make your own rot proof timber
- How to Drive for free: Bio-tuning a VW Caddy Van
- How to make a Garden Bench with the Chainsaw
- Reuse a Washing Machine Motor, Make an upcycled multi-tool!
- Spray Paint your own Car or Van in a DIY Shop Spray Booth
- Cheap but Capable Compressed Air System
- Dremel Moto-Saw 2 in 1 Scroll/fret saw
- Is it worth skimming a brake disc rotor?
- More Tips n Tricks to Make Great Lumber with a Chainsaw Mill
- Mending Stove top Ecofan’s Achilles Heel
- Making Quick Clamp Hold Downs from Scrap
- 17 Super Tips for Chainsaw Milling
- Making a Hybrid Knife Holder from Firewood
- Alaskan Style Chainsaw Mill vs Band Mill
- Hacking my Band Saw
- Turning Scrap Car Parts into Funky Upcycled Furniture
- Making an Oak Breakfast Bar
- Making a Stove Top Fan From Junk
- Upcycled Workshop Stove Experiment – Five Years On
Outside FE
Flowering Elbow | | Log in